When you start growing a snake plant, you probably will faced some problems. One of them is when your snake plant turning black. But don’t worry you still can learn how to fix them!
Snake Plant Turning Black Cause Of Overwatering
one of the reason snake plant turning black is because of overwatering. After that, plant the part of the plant that was close to the bottom in well-draining soil. Succulent soil, or a similar growing media, is ideal for this. In approximately a month, the plants will start to establish roots, and in another month, they will sprout new growth.
Overwatering is the most prevalent reason for snake plants turning black. Snake plants are native to Africa, where they thrive in arid climates with little rainfall.
You are overwatering your snake plant if you are watering it more than once a week. This is especially true in the winter when snake plants go dormant and stop growing, reducing their demand for moisture. Watering once a month (with a good soak to encourage healthy roots) is required to avoid root rot (if your snake plant is not growing, read my article for the reasons why and how to solve it).
Too much water around the roots from repeated watering encourages the fungus root rot, which causes the snake plant’s leaves to turn black.
Snake plants frequently become yellow and droop as a result of excessive watering, with black leaves indicating root rot.
How can it be saved… Reduce the amount of water you use. Snake plants should be irrigated in a cycle of soaking the soil and then allowing it to dry fully to mimic the conditions in which they grow in their natural habitat.
Snake plants prefer to be watered every two weeks, but the easiest approach to figure out the right watering frequency for your environment is to feel the soil at the bottom through the drainage hole in the base to see if it’s dry or wet.
Snake Plants in the Water If the soil is dry, now is the time to water; if it is still wet, wait until it dries before watering.
Once rot has set in, reviving a snake plant can be tough. Because black rot spreads and eventually kills the plant if left untreated, the best approach is to trim back any black areas from your snake plant and leave only healthy tissue. The plant has a possibility of regrowing once the black infected area of the plant has been removed and your watering procedures have been adjusted.
If a large portion of your snake plant has turned black, it will be difficult to revive it, and the plant will most likely die back. I propose taking cuttings for propagation if there is any healthy tissue on the plant. Snake plant propagation from cuttings is simple and has a high success rate.
Pots Without Drainage Holes
The other reason why snake plant turning black is because of the pot doesn’t have drainage holes. Snake plant leaves can turn black due to water stress since they are grown in pots with no drainage holes in the bottom, allowing water to collect around the roots. If your snake plant is in a pot that doesn’t have drainage holes, repot it right away to save it. Snake plant leaves going black is caused by a variety of factors, including a lack of drainage holes in the pot’s base.
Saucers and trays are used. If you have a saucer or tray underneath your pot to protect water from overflowing, it should be emptied periodically to allow excess water to escape rather than pooling around the base of your pot, which causes root rot.
Snake plants are frequently marketed as gifts in stores, with a fancy outside pot. This pot can prevent excess water from escaping, resulting in water stress and the blackening of your snake plant’s leaves.
Pots that don’t have drainage holes in the bottom.
Snake plants require the soil to dry out between waterings to avoid rot and blackening of the leaves, so make sure your snake plant is in the right pot and that excess water can drain after watering.
Cutting away any black leaves back to healthy tissue and propagating from cuttings if necessary applies to snake plants that are water stressed for any other reason.
Conclusion
When there is too much moisture around the roots due to overwatering, slow draining soils, or pots lacking drainage holes at the base, snake plants turn black due to root rot. High humidity might also contribute to the blackening of the leaves.
Reduce the amount of watering, replace the soil with succulent and cactus soil, and place the snake plant in a drainage-friendly pot. Avoid placing the snake plant in a place with high humidity, such as bathrooms or kitchens.